Onda Lifting: What Approach is Used for the Procedure?

1. Customized design and handpiece utilization plan before the procedure
The medical team meticulously designs the lifting treatment before the procedure. They carefully analyze areas requiring skin elasticity improvement and contour refinement to plan the use of 3mm and 7mm handpieces. Areas where volume loss (sunken cheeks) is a concern are carefully avoided, while areas needing tightening receive concentrated energy delivery.

2. Appropriate energy settings for each individual
For facial areas, energy settings ranging from 60,000 to 120,000 joules can be considered. Rather than simply applying a high amount of energy, a customized design that takes into account the individual's skin condition and treatment goals is crucial.

3. Delicate speed control
During Onda treatment, the method of heat delivery within the tissue can vary depending on the handpiece's movement speed. The medical team slows down the speed in areas where sufficient heat accumulation is needed and speeds it up in sensitive areas. This can help reduce unnecessary overheating and elicit the desired thermal response.

4. Shot distribution plan by area
The use of 3mm and 7mm handpieces is carefully determined, considering each patient's individual volume and fat distribution. For example, for patients with relatively less fat, the 3mm handpiece is primarily used, while for those with more fat in the double chin or lower jaw area, the proportion of the 7mm handpiece is adjusted during the procedure.

Subtle Differences in Onda Lifting Treatment Methods
During Onda Lifting treatment, instead of proceeding with a constant 90W output from the start,
in some cases, a method is applied where high output of 100-110W is used in the initial stage of the treatment to quickly raise the skin tissue temperature, then maintained at 90W.

Differences considered in the treatment method
Reduced time to reach thermal reaction:
Even when the same total energy is applied, starting with high output tends to raise tissue temperature more quickly.
This can reduce the time it takes for enough energy to accumulate and reach the desired thermal reaction zone.
Consequently, the point at which skin tissue begins to react can be accelerated.
Reduced energy loss in the main reaction layer:
Applying high output for a short duration can help achieve the target temperature before thermal energy widely dissipates into surrounding tissues, and
as a result, it can be expected to induce the desired reaction primarily in the dermis and subcutaneous fat layers without causing significant damage to the epidermis.
Effective heat transfer relative to treatment time:
If the treatment is performed with a constant output of only 90W, it may take longer to reach the desired thermal reaction zone.
It may also require more shots to induce a sufficient thermal reaction.
In contrast, starting with high output delivers the necessary thermal energy in a relatively short time,
and thereafter, the output can be adjusted to consider the stability of the treatment.
Expected effects after treatment:
Compared to the traditional 90W standalone treatment,
you may experience the lifting effect more quickly, and
you can expect a feeling of tightened and firmer skin immediately after the treatment.
Since the output is adjusted before an excessive feeling of heat occurs,
this can help reduce pain or discomfort that may arise during the treatment.
Thus, even with the same total energy, depending on the output control method,
treatment results may vary, and
this can be a factor influencing post-treatment changes.

Key Characteristics of Onda Lifting

Lifting and Tightening Together
Onda Lifting uses ultra-short microwave (2.45GHz) to deliver heat to the dermal and subcutaneous fat layers. This allows for simultaneous lifting and tightening effects.

It utilizes the principle of vibrating water molecules within the skin to generate frictional heat. This helps in collagen contraction and production, and affects fat cells, allowing for a lifting effect to occur.

Microwaves cause energy absorption in the skin's water layers, generating heat. Thanks to this characteristic, it can selectively deliver energy to the dermis and subcutaneous fat layers while minimizing direct stimulation to the epidermis.

A distinguishing feature of the Onda device is its ability to deliver both lifting and tightening effects simultaneously with a single treatment.

온다 시술은 핸드피스 이동 속도에 따라 조직 내 열 전달 방식이 달라질 수 있습니다. 의료진은 충분한 열 축적이 필요한 부위에서는 속도를 늦추고, 민감한 부위에서는 속도를 빠르게 조절합니다. 이는 불필요한 과열을 줄이고 원하는 열 반응을 이끌어내는 데 도움이 될 수 있습니다.

4. 부위별 샷 분배 계획

3mm와 7mm 핸드피스의 활용은 환자 개개인의 볼륨감과 지방 분포를 고려하여 신중하게 결정됩니다. 예를 들어, 지방이 비교적 적은 환자분들께는 주로 3mm 핸드피스를 활용하고, 이중턱이나 하관 부위에 지방이 많은 경우에는 7mm 핸드피스의 비중을 조절하여 시술을 진행하게 됩니다.

온다리프팅 시술 방식의 섬세한 차이점

온다 리프팅 시술 시, 처음부터 일정한 90W 출력으로만 진행하는 방식 대신,

시술 초반에는 100~110W의 고출력을 사용하여 피부 조직의 온도를 빠르게 올리고, 이후 90W로 유지하는 방식을 적용하는 경우가 있습니다.

시술 방식에서 고려되는 차이

열 반응 도달 시간 단축:

동일한 총 에너지를 조사하더라도, 고출력으로 시작하는 경우 조직 온도가 보다 빠르게 상승하는 경향이 있습니다.

이는 에너지가 충분히 누적되어 원하는 열 반응 구간에 도달하는 시간을 줄여줄 수 있습니다.

결과적으로 피부 조직이 반응하기 시작하는 시점이 앞당겨질 수 있습니다.

주요 반응층에서의 에너지 손실 감소:

고출력을 짧은 시간 동안 적용하면 열 에너지가 주변 조직으로 넓게 퍼지기 전에 목표 온도를 달성하는 데 도움이 될 수 있으며,

이로 인해 표피에 큰 손상을 주지 않으면서 진피 및 피하지방층을 중심으로 원하는 반응을 유도하는 것이 기대될 수 있습니다.

시술 시간 대비 효과적인 열 전달:

만약 90W의 일정한 출력으로만 시술을 진행하면, 원하는 열 반응 구간에 도달하기까지 시간이 더 소요될 수 있습니다.

충분한 열반응을 유도하기 위해 더 많은 샷 수를 필요로 할 수도 있습니다.

그에 비해, 고출력으로 시작하는 방식은 비교적 짧은 시간 안에 필요한 열 에너지를 전달하며,

이후에는 출력을 조절하여 시술의 안정성을 고려할 수 있습니다.

시술 후 경험할 수 있는 기대 효과:

기존 90W 단독 시술과 비교하여

리프팅 효과를 좀 더 빠르게 느끼게 될 수 있으며,

시술 직후 피부가 당겨지고 탄탄해지는 느낌을 기대할 수 있습니다.

열감이 과도하게 느껴지기 전에 출력을 조절하게 되므로,

시술 중 발생할 수 있는 통증이나 불편감을 줄이는 데 도움이 될 수 있습니다.

이처럼, 동일한 총 에너지를 사용하더라도 출력 조절 방식에 따라

시술 결과는 다르게 나타날 수 있으며,

이는 시술 후 변화에 영향을 미치는 요소가 될 수 있습니다.

온다리프팅의 주요 특성

리프팅과 타이트닝을 함께

온다리프팅은 극초단파 마이크로웨이브(2.45GHz)를 사용하여 진피층과 피하지방층에 열을 전달합니다. 이를 통해 리프팅 및 타이트닝 효과를 동시에 기대해 볼 수 있는 장비입니다.

피부 속 수분 분자를 진동시켜 마찰열을 발생시키는 원리를 이용합니다. 이는 콜라겐의 수축 및 생성을 돕고, 지방세포에 영향을 주어 리프팅 효과가 나타날 수 있도록 합니다.

마이크로웨이브는 피부 내 수분층에 에너지가 흡수되어 열이 발생합니다. 이러한 특성 덕분에 표피에 직접적인 자극은 줄이면서, 진피 및 피하지방층에 선택적으로 에너지를 전달할 수 있습니다.

온다 장비는 하나의 시술로 리프팅과 타이트닝 두 가지 효과를 동시에 기대할 수 있다는 점이 특징입니다.

Onda treatment is designed to achieve two goals simultaneously: lifting focused on facial contour improvement, and tightening for skin texture and elasticity enhancement.

How Onda Lifting Works

For Onda Lifting treatments, two types of handpieces, 3mm and 7mm, are used.

The 3mm handpiece is designed to deliver energy to the boundary between the dermis and subcutaneous fat.

When heat is delivered to this depth, the production of collagen and elastin fibers can be induced, and the skin is expected to experience immediate tightening through the promotion of hyaluronic acid production and the contraction of existing collagen.

In areas of fat with edema, water reduction is induced, allowing you to notice changes in your facial contour immediately after the treatment.

The 7mm handpiece reaches deeper into the subcutaneous fat layer, selectively damaging fat cell membranes and inducing cell death.

Damaged fat cells can be expelled from the body through lymphatic circulation, which is expected to result in a more defined facial contour. Typically, changes begin to appear after 2-3 weeks, with contour improvement visible by the 4th week, and the most satisfactory results can be expected 6 weeks after the treatment. Once fat cells are destroyed, they do not regenerate, ensuring long-lasting results.

During the treatment, the retaining ligaments contract immediately, allowing you to experience a lifting effect right away.

Importance of Temperature Control: Collagen in the dermal layer can be most actively induced to contract within the temperature range of approximately 60-65 degrees Celsius. Therefore, a treatment technique that slowly moves the handpiece to accumulate sufficient energy to reach this optimal temperature is crucial.

Water-Selective Energy Absorption: Microwaves have the characteristic of selectively delivering energy only to water. Thanks to this, stimulation to nerves or blood vessels is minimized, and thermal energy can be delivered intensively only to fat cells and the water layer within the dermis. As a result, a lifting treatment can be performed with reduced pain and a lower likelihood of side effects.

Combining with Other Lifting Treatments

At our medical institution, Onda Lifting can be performed as a standalone treatment, but when combined with other treatments such as Shurink (fascia layer focused treatment) or Oligio (radiofrequency elasticity enhancement), synergistic effects can be expected.

Especially when receiving multiple treatments on the same day, the time required for heat accumulation is shortened, leading to even greater satisfaction after the treatment.

Our Medical Team's Treatment Philosophy

We perform Onda Lifting treatments multiple times every day.

However, the lifting design for each patient is meticulously customized to account for individual characteristics.

Even after the treatment, our medical team constantly researches and considers how to deliver better lifting results to patients.

This is because we believe that true lifting treatment goes beyond simply operating equipment; it involves a deep understanding of the patient's skin texture and overall facial contours, and delicately designing harmonious contour changes within that understanding.

Onda Lifting goes beyond the performance of the device itself; it can create a difference through the skilled expertise and meticulousness of the medical team performing the treatment.

We invite you to experience this difference firsthand.

Onda Lifting's Immediate Effects: How Does It Work?

Onda Lifting is a method that utilizes microwave energy to selectively concentrate heat only in the deep 3mm and 7mm layers of the skin.

In this process, collagen fibers are rapidly heated to a temperature of 65 degrees Celsius or higher, which can cause an immediate contraction response.

As a result, you will be able to directly feel the changes in the lifting effect immediately after the treatment.

You can experience changes within a short period after the treatment,

The fact that you can immediately feel skin elasticity and lifting effects after treatment is one of the key features of Onda Lifting.

For those who desire quick results, we recommend considering Onda Lifting.

Onda Lifting Treatment Process

1. Precise Pre-Treatment Design and Handpiece Strategy Formulation

At our medical institution, we consider precise design planning before Onda Lifting treatment to be a crucial step.

Our medical team directly consults and comprehensively analyzes the patient's skin elasticity, fat distribution, facial volume, and the direction where lifting is needed, then plans suitable treatment areas for each individual.

Based on this analysis, the 3mm handpiece (dermal layer focus) and 7mm handpiece (fat layer focus) are appropriately applied to each treatment area.

This is not merely about using equipment; it is an approach that aims for patient-specific strategic lifting centered around design.

2. Optimal Energy Delivery and Precise Settings

The total amount of energy delivered during Onda Lifting treatment is a very important factor.

We can perform treatments customized to the patient's condition, ranging from 60,000 joules to over 120,000 joules, and we meticulously plan and apply appropriate treatment times for the given energy level, along with cooling strategies to prevent overheating.

3. Handpiece Speed and Heat Accumulation Control

The effectiveness of Onda treatment can vary depending on the degree of heat accumulation in the treated area.

In the initial stages of treatment, we move the handpiece slowly to ensure sufficient heat accumulation, and in the latter stages, we switch to a faster speed to minimize the risk of burns to the skin surface.

Delicate control of the procedure is based on extensive experience.

4. Customized Handpiece Allocation and Treatment Plan Establishment

The treatment plan must be tailored to your face shape and skin condition. For instance, the approach may differ for individuals with plump cheeks versus those experiencing only a loss of elasticity.

We meticulously assess your volume distribution, fat location, and skin thickness to adjust the usage ratio of 3mm and 7mm handpieces.

For example, we primarily use the 7mm handpiece for areas with a thick fat layer, such as the jawline, and focus on the 3mm handpiece for the area directly below the cheekbones where volume loss might be a concern.

Beyond a simple energy delivery method, we apply a handpiece distribution strategy optimized for each individual.

5. Meticulous Design and Continuous Research by Medical Professionals

Based on extensive Onda Lifting treatment experience, we adopt a careful approach for every appointment.

The treatment design varies for each individual's facial characteristics.

Our medical team continuously simulates your facial changes from various angles outside of consultation hours, diligently researching more effective energy settings and handpiece placements.

While Onda Lifting equipment itself is highly accessible, the expected results can vary depending on who designs and performs the treatment.

Onda Lifting is not just about using the device; it's a procedure where the practitioner's delicate judgment and skill are crucial.

Recommended for

• 01. Those seeking improvement in double chin, deep jowls, and jawline definition.
• 02. Those concerned about deepened nasolabial folds and skin sagging.
• 03. Those who felt unsatisfied with contour and elasticity improvement from previous lifting treatments.
• 04. Individuals in their 30s to 50s experiencing both fat accumulation and reduced skin elasticity.
• 05. Those wishing to minimize discomfort during treatment or concerns about recovery time.

Treatment Benefits

• 01. Excellent cooling function helps reduce discomfort during the procedure.
• 02. You can expect a tightening effect after the treatment.
• 03. You can return to your daily life immediately after the treatment.

Treatment Process

• STEP 01. After cleansing your face thoroughly, you will have a 1:1 consultation with a professional medical team.
• STEP 02. Carefully apply oil to the treatment area.
• STEP 03. Proceed with the customized Onda Lifting treatment.

Post-Treatment Precautions

• ㆍYou can wash your face and apply makeup from the day of the procedure.
• ㆍIt is recommended to avoid saunas, jjimjilbangs (Korean bathhouses), alcohol, and smoking for about 1 week after the procedure.
• ㆍOccasionally, you may feel dryness due to warmth in the treated area, so please apply moisturizer regularly to keep your skin hydrated.
• ㆍWhen going out, it is recommended to meticulously apply sunscreen to protect your skin from UV rays.